Well show you to create a bootable USB flash drive with the Windows 10 installer from a Mac. To our surprise there was nothing out there that.Its due to some reasons that my 4 GB flash drive encountered an unusual problem that i have to fix later.:D. 4 If the Flash will not boot, read over the following tipsThere was a separate track for each Mac/Windows/Linux and several manual and error-prone steps along the way. Making a bootable driver is not similar to copying an ISO image file directly on the USB flash drive. In this short guide, we will show how to make or create a bootable USB from ISO file on all Windows version computers. Essentially, creating bootable USB drivers to install operating system of your choice varies from each Windows and Mac versions.Use a good quality Flash such as: And there is still value in the advanced troubleshooting tips below.>Be sure to review the Hardware Compatibility page when designing your server.The unRAID Server OS is designed to be installed on, and boot from a USB Flash storage device, 512MB or larger. The instructions below do still work, and are necessary for installing versions of unRAID earlier than v4.6 Final, and for preparing a flash drive on a Mac. With the advent of the all-in-one releases (as of v4.6 Final), a make_bootable.bat batch installation file is included, that replaces the use of the syslinux utility in preparing the flash drives for booting unRAID.
Plug in your USB Flash drive and format it using Disk Utility. syslinux - a collection of linux tools that will allow you to make the drive bootable1. unetbootin - installs unRAID on your flash drive for you Unmount the partition by clicking "Unmount" in the top menu Check the "Show Details" box and get the device path for your disk, ex: /dev/disk2s1 Choose the UNRAID partition from the list on the left Click Options and make sure Master Boot Record is selected Please make sure to read carefully to know when to select "Device" or "Partition" At the > prompt type the following and press enter between eachNote: if you get an error about the device not being available for writing, ensure you have Unmounted the partition in Disk Utility Type the following command, substituting for your raw deivce name ex: /dev/rdisk2 and press enter So if your partition device path was /dev/disk2s1, the raw device name is /dev/rdisk2, basically you drop the s1 off the end (that's the partition number) and add in a r before disk Now you'll need the raw disk device name. Open Terminal (Applications -> Utilities -> Terminal) Install the bootable MBR on your flash drive with the following command (again substituting for your raw device name)Dd conv=notrunc bs=440 count=1 if=mbr.bin of=4. cd to that folder in terminal by typing the following (you may need to change the version number to match your download) Unzip/tar your syslinux download (you can leave it in the Downloads folder Prepare A Flashdrive In For Windows Boot Iso Open UnetbootinChoose Disk Image at the bottom and browse for your unRAID iso Open unetbootin (it will need your password) Change the extension of your unRAID download from zip to iso If it does not boot to the unRAID boot screen that displays a choice of starting unRAID or Memtest, reboot your server and enter the BIOS setup. Power up your server and see if it immediately boots (with some motherboards it will). So if any one has Windows or Linux can you try this and write here if it works there also.Safely remove/eject the Flash from your PC and plug it into your server. When it finishes, you can eject your USB Flash Drive and put it in your unRAID server and power it upI Think this would work with Windows, Linux versions also. For more general BIOS suggestions on getting a machine to boot the USB flash drive, check here, near the bottom of the page. For machines with an AMI BIOS, check here. Be aware that some motherboards will change the boot order when you add hard drives, and you will have to return to these same BIOS screens to re-select your flash drive.Note: You may need to check here for more BIOS Setup Tips and Other BIOS Suggestions. Save your BIOS settings and try to boot the Flash. In some BIOS, the flash drive may show up in the list of hard disks, and you may have to select it there. Make full screen by defualt for mac high sierraA U3 removal tool specific to SanDisk drives can be found here. U3 Un-Install software is available here. If your flash drive had pre-installed "U3" software, it will need to be removed before you format and install unRAID on it. If one does not work for you, try another. The following tips are what users have found to work, in different situations. Some combinations of motherboard, BIOS, and flash drive do not work, or only work after more advanced 'modifications'. The alternate geometry will often will make it possible to use your flash drive as a boot disk when your BIOS does not work with the existing geometry. It sets the Cylinders/Heads/Sector geometry of a flash drive to an alternate set of geometry values. You may need to use the HP formatting tool to make your flash drive bootable on your BIOS. Try formatting the USB drive as FAT instead of FAT32 If your flash drive does not have a preloaded master boot record and a partition marked as "active", then it is unlikely to boot unless you use the -ma options. Sandisk 16GB Cruzer Contour & Amicroe 32GB). Some have had problems with the version named SP27608.exe. The version of the HP USB Format Tool that works best has a file name of SP27213.exe. Apparently, there is more than one version of the HP format tool.
0 Comments
Leave a Reply. |
AuthorMarissa ArchivesCategories |